VERTICAL LIFT MODELS
Our vertical lifts options range between 1600 lb and 8000 lb capacities and can be used with all different types of hull designs including pontoons and tritoons. These lifts are freestanding and do not require any type of anchoring. The lifts are designed to be placed along side of a dock or seawall.
Our lifts utilize an I-beam platform design for strength and reliability, but they are also designed for lower water application and allows the cradle to drop down into the lower framework. This allows our lifts to work as well as V-rack boat lift designs.
KEY VERTICAL LIFT COMPONENTS
- Vinyl and Aluminum Hull Bunks – This design allows the bunk to contour to the hull of your boat and the vinyl cap will not trap debris like carpeted bunks. The bunks are also little to no maintenance with the vinyl and aluminum combination.
- I-Beam Cradle Design – A very strong platform design using a straight I-Beam extrusion. Our design drops into the lower framework allowing the cradle to get just as low as a V-style cradle design.
- Patented Double Reduction Winch – Easier to crank than other comparable capacity lifts.
Below you will find our vertical lift models along with some lift specifications. All vertical models come standard with vinyl and aluminum hull bunks, stainless steel cables, galvanized steel winch cable and zinc plated fasteners.
Inside Beam Width
|MH-V25108||2500 lb||108″||108″||325 lbs||52″||30″||9′|
|MH-V35108||3500 lb||108″||120″||380 lbs||64″||54″||10′|
|MH-V35120||3500 lb||120″||120″||420 lbs||64″||54″||10′|
|MH-V45108||4500 lb||108″||120″||470 lbs||64″||54″||10′|
|MH-V45114||4500 lb||114″||120″||495 lbs||64″||54″||10′|
|MH-V45120||4500 lb||120″||120″||500 lbs||64″||54″||10′|
|MH-V60120||6000 lb||120″||132″||620 lbs||60″||30″||12′|
|MH-V60132||6000 lb||132″||132″||635 lbs||60″||30″||12′|
|MH-V60144*||6000 lb||144″||132″||680 lbs||60″||30″||12′|
|MH-V70144*||7000 lb||144″||168″||835 lbs||60″||30″||12′|
|MH-V80120||8000 lb||120″||132″||750 lbs||60″||30″||12′|
|MH-V40120HL High Lift||4000 lb||120″||120″||580 lbs||84″||54″||10′|
|MH-V60120HL High Lift||6000 lb||120″||132″||775 lbs||84″||30″||12′|
|*For Pontoon Boats Only|
ACCESSORIES FOR VERTICAL LIFTS
|Accessory Type||Description||Fits Lifts|
|Standard Canopy||Standard canopy frame, legs and vinyl cover||Vertical|
|High Top Canopy||High Top canopy frame with legs and cover||Vertical|
|Carpeted Load Guides||Full Length Carpeted Guides||Vertical|
|Foam Load Guides||Foam covered uprights, covers available||Vertical|
|Pontoon Guides||Angled Bracket with vinyl and aluminum guide runner||Vertical|
|Motor Stop||Used with outboards and I/O’s to protect them from making contact with rear crossmember.||Vertical|
SAFETY AND GENERAL INFORMATION
Loading A Vertical Lift
When loading a boat on the hoist you should have close to equal the weight on front and back of your hoist. Correct loading typically will have the rear of boat (where the motor is located) close to the rear of the hoist. Exceptions could be either a ski or sail boat.
If too much weight is on the front or back of the hoist the cables could become bound on the pulleys, which can cause problems when lowering your boat. The hoist may lower only on one corner. If this happens, try using a counter weight in the light end of the boat to ensure equal weight distribution. This should cure the problem.
Canopy And Wind
The hoist becomes much lighter when removing the boat from it. So it is important to keep in mind that when your boat is not on the hoist strong winds can move, tip over or even pick it up out of the water.
Our Craftlander line of products are only sold through established dealers.
Please call 1-888-NUCRAFT (1-888-682-7238) or send us an email to obtain the name of the dealer near you. eMail: firstname.lastname@example.org
© 2015 NuCraft Metal Products